foame3d, Modele
[ Pobierz całość w formacie PDF ]
Control Horn Detail
.032 wire control rods
Use Du-Bro Micro E/Z Links
OR
Strip plastic cover
from small gauge wire
and CA to ends of
control rods
Wing cut from one piece of Depron foam
Fabricate control horns
from spare micro servo
control arms or nylon
Zip-Ties.
Hinge Detail
4mm carbon fiber tube. Cut a channel (per plan) on the bottom of the
wing only and CA or use RC Z 56.
Use 1” wide clear packing
tape for hinges. Clean all parts with
rubbing alcohol before taping.
Ta p e
FOAMe-3 D PARK FLYER SPECS
PROVEN SYSTEM RECOMMENDATIONS
MATERIALS LIST
Wing Span....... 37”
Lienth............ 37.5”
Weight............12-13oz
Power.............GWS EPS350C
Max 3D Power... Brushless motor fit
to GWS EPS350D gearbox
Prop.............. GWS 11x4 -- 12x4
Ch................ 5
Battery.......... 2-3 Cell-700 to 1200mAh-Li-Poly
Rx and Servos
* GWS R-6NII 5ch receiver or Hitec Electron 6 FM
* 4 Waypoint W-084 Micro Servos
or Hitec HS 55
Brushed Motor
(Good performance)
* GWS EPS350C “DS” Gearing Motor
* GWS ICS-300 Speed Controller
* Prop GWS 12x6 Slow Flyer
* 3 Cell-800-1200mAh-11.1v Li-Poly Battery
Brushless Motor
* AXI 2212/34 outrunner
(Max performance)
* Phoenix 25amp speed controller
* 3 Cell 700-1200mAh-11.1v Li-Poly Battery
* APC 12x3.8 electric slow flyer
OR...
* HiMaxx 5100 or 5400
(Max performance)
w/GWS 350C “DS” gearbobx
* Phoenix 25amp speed controller
* 3 Cell 700-1200mAh-11.1v Li-Poly Battery
* APC 12x3.8 electric slow flyer
* Depron 6mm White (www.depronusa.com)
* 30” 4mm & 2mm wrapped carbon fiber tube
* Medium or Thick foam friendly CA
* Foam friendly CA accelerator
* JZ Products Super RC “Z’ 56 glue
* 1” Self-sticking Hook & Loop (Velcro) tape
* Clear packing tape
* 4 Du-Bro Micro Control Horns No. 848
* 4 Du-Bro Micro E/Z Links No. 849
* 1” wide self-sticking hook & Loop (Velcro)
* .032 wire control arms
* 1/2” Nylon Filament Strapping (3M brand)
* Zagi tape for trim scheme (optional)
* Straight edge razorblades
* No. 11 Xacto knife
* Metal yardstick
* 3M Photomount Spray Adhesive
(for plan transfer to Depron)
Alternative AXI Brushless Motor setup
Groove and glue in 4mm wrapped carbon tube
AXI 2212/34 External Rotor Brushless
Lighty coat back of plan parts with
Spray Adhesive, apply each part to
Depron. Carefully cut each part out
using a strightedge and #11 Xacto.
Dry fit assembly--check alignment
A Rotary Tool Cutting Adapter is
perfect for clean easy to make
grooves for Fiber Carbon rod
stiffiners.
Colored Zagi tape works great for trim. It’s best to trim each part before assembly.
® Copyright 2004 3Dbatix.com. All rights reserved.
1/8” light plywood radial mount,
reinforced with Depron triangle stock
on all 4 sides
Drill 3/16 (4mm) hole in back end of hardwood block.
Make sure hole is slightly big to allow for adjustment
while fitting and gluing. Use epoxy for this step.
Denotes cut-lines
4mm wrapped carbon tube fuselage stiffener. Groove foam
and glue with order-free (foam freindly) CA or JZ Products
Super RC Z 56
GWS EPS350C “DS” Gearing
Rudder Servo
Elevator Servo
Initial CG 3.5 - 4” from leading edge root
.032 Wire Pushrod
3/8” square (light) hardwood block
mounts to the GWS gearbox assembly
Control Horns (Du-Bro Micro)
Pull-Pull rudder set-up. Use Du-Bro EZ connectors and heavy button tread or fishing line
0
2-3 Cell
700-1200 mAh
Li-Poly Battery
Aileron Servo
Note: Mount speed controller as close to motor as possible.
1
2
Note: Battery location is approximate. Adjust accordingly based
on battery weight, dimensions and desired flight characteristics.
Mount using self-sticking hook and loop (Velcro) tape.
Inch Scale reference,
check after printing.
3
4
3
2
1
0
Landing gear optrional. For scale appearence only.
All airframe parts and control surfaces are cut from 6mm Deporn Foam
[ Pobierz całość w formacie PDF ]