foame2x, Plany depronowców
[ Pobierz całość w formacie PDF ]
FOAMe IIx 3D Park Flyer
Designed by Steven Gibson
Bottom wing cut from one piece of 6mm Depron foam
Strengthened with 4mm carbon fiber tube (bottom wing only). Cut a
channel (per plan) on the bottom of the bottom wing only and CA or
use RC Z 56.
Cut 6mm slots for strut tabs.
Dry fit and trim excise.
Aileron servos.
Use Dubro Mini
E/Z Connetors
for easy ajustments.
Mount using 3M
Double Coated
Industrial Foam Tape
Rear
Front
Front
Rear
Bottom Wing
TOP wing cut from one piece of 6mm Depron foam
Cut 6mm slots for strut tabs.
Dry fit and trim excise.
Aileron to aileron control horns. Cut a
slot for horn dry fit, remove and CA back
in place. See aileron detail diagram.
Tip: Fabricate Aileron to
Aileron control horns out of
Dubro Micro 90 Bellcranks.
Use medium CA to secure.
Wing
Top Wing
Top/bottom tabs are extended to allow for flush
trimming during dry fitting of wing.
Glue scrape Depron triangles for
extra strength
.8mm carbon rod landing gear
support/stiffener. Groove foam and glue
with order-free (foam friendly) CA or JZ
Products Super RC Z 56
NOTE: landing gear shown is not functional
but is recommended for improved flight
performance
Rudder cut line
Xbrace fuselage stiffener. Glue with order-
free (foam freindly) CA or JZ Products Super
RC Z 56
Denotes cut-lines
AXI 2208/34
External Rotor
Brushless
Remove Material
Remove Material
Remove Material
Remove Material
Note: Mount speed controller as
close to motor as possible.
Rudder Servo
Elevator Servo
Pushrods - .070 Carbon Fiber Rod with .032 Wire Ends
2-3 Cell
700-1300 mAh
Li-Poly Battery
Dubro Micro
Tail Skid
Notch 1/8 lite plywood AXI
motor mount 6mm at
top/bottom.
Bottom Tab
1/8” light plywood radial mount,
reinforced with Depron triangle stock
on all 4 sides
Bottom Wing
Note: Battery location is approximate. Adjust
accordingly based on battery weight, dimensions
and desired flight characteristics. Mount using
self-sticking hook and loop (Velcro) tape.
0
FOAMe IIx 3 D PARK FLYER SPECS
FLIGHT SYSTEM RECOMMENDATIONS
MATERIALS LIST
HINGE DETAIL
PUSHROD DETAIL
1
Wing Span....... 30.5”
Length............33”
Weight............14-15oz
Power............. AXI 2212/34
Prop.............. GWS 12x6 Slow flyer
Ch................ 5 (4 servos + speed controller)
Battery.......... 3 Cell-700 to 1320mAh-Li-Poly
Rx and Servos
* GWS R-6NII 5ch receiver or equivalent
* 4 Waypoint W-084 Micro Servos
or Hitec HS 55
Brushless Motor
* AXI 2212/34 outrunner
(Max 3D performance)
Speed Controller
* Phoenix 25amp speed controller
Battery
* 3 Cell 700-1350mAh-11.1v Li-Poly
Prop(s)
* GWS 12x6 Slow Flyer
* APC 12x3.8 electric slow flyer
* Depron 6mm (www.depronusa.com)
* 30” 4mm & 2mm wrapped carbon fiber tube
* .070 Solid Carbon Rod (push rods + stab support)
* .080 Solid Carbon Rod (landing gear support)
* Medium or Thick foam friendly CA
* Foam friendly CA accelerator
* JZ Products Super RC “Z’ 56 glue
* 1” Self-sticking Hook & Loop
(Velcro-Industrial Strength) tape
* Clear packing tape
* 4-E-flite Micro Control Horns No. EFLA200
OR...4 Du-Bro Micro Control Horns No. 848
* 4 Du-Bro Micro E/Z Links No. 849
* .032 wire control arms
* Du-Bro RC Electric Flyer Hinge Tape (3M Blenderm)
* Zagi tape for trim scheme (optional)
* Straight edge razor-blades
* No. 11 Xacto knife
* Metal yardstick
* 3M Photomount Spray Adhesive
(for plan transfer to Depron)
Best results are achieved by using 1”
wide Du-Bro RC Electric Flyer Hinge
Tape (3M Blenderm) for all hinges.
Clean all parts with rubbing alcohol
before applying.
Use on control servo arms.
CA 3” of wire to 2mm carbon fiber rod,
secure with 1” of heat shrinking tubing.
Carbon rod fits opposite side of control
arms, wire connects and holds rod in place
Reinforce carbon rod
landing gear crossing
with 1/32 ply
Ta p e
.032 wire control rods
2
.040 Solid Carbon Rod push rods
Inch Scale reference,
check after printing.
Bevel leading edge
of all control sufaces 45º
3
Heat shrink tubing
Look for more bulid tips online at: 3Dbatix.com
® Copyright 2005 3Dbatix.com. All rights reserved. rev-3.0205
Lighty coat back of plan parts with
Spray Adhesive, apply each part to
Depron. Carefully cut each out
using a strightedge and #11 Xacto.
Carefully cut each out using a
strightedge and #11 Xacto.
Dry fit assembly--check alignment.
A Rotary Tool Cutting Adapter is
perfect for clean, easy to make,
grooves for Fiber Carbon rod
wing spar. Glue spar in with
RC Z 56 or medium/thick CA.
Apply trim scheme before final
assembly.Zagi tapw works great! It’s
best to trim each part before assembly.
Assemble using RC Z 56 or medium or
thick CA. great for trim.
4
3
2
1
0
All airframe parts and control surfaces are cut from 6mm Deporn Foam
[ Pobierz całość w formacie PDF ]